Four Winds Hat

Four Winds Hat

Okay, I should begin any description of this hat with an admission: that I bought the yarn for my husband, and originally intended to design this bad boy for him. Then, however, the yarn told me that it didn't want to belong to him, it wanted to belong to me instead. And then it said that this was the form that it dreamed of taking...

... sure, I'm exaggerating a bit. Truly, though, this design was 100% inspired by the fiber, and creates a very plush, delicious hat because of the twisted stitch pattern. Of course, since ALL of the stitches are twisted every other row it's a tad annoying to work, but I think the end result is definitely worth it!

Yarn: Malabrigo Worsted (100% Merino Wool; 210 yards [191 meters]/100 grams); #56 Olive - one skein 

A closer look at the stitch pattern and the
crown.

Needles: One 16" circular needle in size US 6, one 16" circular needle in size US 9, and one set of double pointed needles (dpns), also in size US 9

Notions: Tapestry needle, four stitch markers

Gauge: 18 stitches = 4 inches in stockinette on size US 8 needles (I'm giving you package gauge in case you're using a substitute yarn)

Okay, so let's make a hat! To start with, then, using your size US 6 needle, cast on 100 stitches loosely, place marker, and join in round. Then, we'll knit the following marker placement row:

Marker Placement Row: (k1, [p1, k1] x 12, place marker) three times; then, k1, * p1, k1; rep from * until you reach the end of the row

Knit this marker placement row. Then we'll work our ribbing, as follows:

Ribbing Row: (k1, * p1, k1; rep from * until you reach next marker, slip marker) four times

Knit this ribbing row until piece measures just over 2". Then, transfer work to your size US 9 circular needle, and continue to work as follows. Notice that you'll need the following terminology to continue (you can find videos below too!):

rt (right twist): knit two together, leaving stitches on left-hand needle; next, insert right-hand needle from the front between the two stitches just knitted together, and knit the first stitch again.  Finally, slip both stitches from left-hand needle together

Nightmare Yarn Hat

Nightmare Yarn Hat
Pictured in Adult Large

Okay, first and foremost, let's get this straight: I'm not actually saying that this yarn (Lana Grossa Colorato Nodo) is a nightmare - I mean, heck, I picked it out, and was pretty darn excited when I saw it! However, as you can clearly see in every picture, this yarn has one peculiarity that makes it difficult to work with - the significant size changes of the fiber, which make roughly 1/10 of the stitches look like they gorged on cured ham until they become monstrously swollen. And because this is not a peculiarity that I noticed until I got the yarn home, my original plan for this yarn was a total disaster - this stuff doesn't take ribbing (who knew ribbing could look terrible!?!?), and looks even worse as a rolled brim (unless you want to look like an incompetent knitter). So, basically, I had to punt. Therefore, I went with the most fool-proof design I could think of, and one that you, too, can put to work for that almost-novelty yarn you accidentally bought and then realized swallows every pattern you put near it (or that you bought on purpose! hi there! no shame, we'll start a club!). (Of course, this pattern is perfectly good for non-nightmarish yarns too!)

Oh, and a quick word on sizing - usually, of course, when you're sizing your hat the biggest concern is head size. That doesn't work quite as well with the nightmare yarn conundrum. And in fact, if you're working with a fiber that isn't predominately wool, you may want to veer in the adult small direction just to accommodate the inevitable stretching.

Sizes: Adult Small (Adult Large)

Yarn: Lana Grossa Colorato Nodo (90% Virgin Wool, 10% Polyamide; 120 yards [110 meters]/50 grams); #109 - two skeins 

A better look at the finish,
the cable, and those pesky big
stitches.

Needles: One 16" circular needle in size US 10, one set of double pointed needles, also in size US 10, one cable needle (cn) or dpn for cabling, and one needle in size US 11 for provisional cast-on

Notions: Tapestry needle, stitch marker, scrap yarn for provisional cast-on

Gauge: 15 stitches = 4 inches in stockinette

So let's make a cute hat from some difficult yarn! Using your size US 11 needle, cast on 18 stitches provisionally. Then, transfer the stitches to either one of your dpns or your size US 10 circular (you can use either since we're starting by knitting flat). Then we'll work the cabled bottom edge of the hat as you'll find below. To do this, you'll need the following notation. And remember you can always cable without a cable needle!

back cross (bc): transfer next 2 stitches to your cn and hold in back; k2, k2 from cn

front cross (fc): transfer next 2 stitches to your cn and hold in front; k2, k2 from cn

Bump Up From Basics Beanie

Bump Up From Basics Beanie
Pictured in Child Size

Okay, I'm doing something a little bit different with this pattern, since I'm not offering it on my website, but through a video tutorial I created on Skillshare instead. Which means that, yes, I've had to face my fear of being on camera (don't worry, I deleted all the takes where I opened my eyes super-wide for no reason), and that this pattern is not technically "free" since it requires a membership on the website to access it. If you sign up through the link above, however, you can get 3 months on the website for $0.99, and access to tons of video content from all sorts of talented and amazing people (and I get some compensation as well!).

Oh, and as far as the actual pattern is concerned - I designed the Bump Up From Basics Beanie as a sort of next-level project for beginning knitters who've gotten comfortable with knitting and purling and are ready to move on to something more complicated. Or in other words, I demonstrate every technique you need to make this hat in the video except for knitting, purling, and tucking in your ends! :)

Anyway, here are the details: